JennAir Range Error Code
A key on the oven control panel is stuck or has an internal short. The oven cannot accept new input commands. Clean the touch panel with a damp cloth — moisture or food residue can cause false key detections. If the code returns after cleaning, the control panel overlay or the EOC board requires replacement.
Note the exact error code and any symptoms
Power cycle — unplug for 60 seconds
Follow the diagnosis steps below
If code persists, call a technician
A key on the oven control panel is stuck or has an internal short. The oven cannot accept new input commands. Clean the touch panel with a damp cloth — moisture or food residue can cause false key detections. If the code returns after cleaning, the control panel overlay or the EOC board requires replacement.
When your JennAir Range displays the F2-E1 code, it means the appliance's self-diagnostic system has detected a fault that requires attention. A single power cycle that clears the code is not a reliable fix if the underlying cause has not been addressed.
Based on our technicians' experience servicing JennAir Ranges, the F2-E1 code is most frequently triggered by:
Before scheduling a service call, work through these steps in order:
If the F2-E1 code returns after completing the steps above, a component has likely failed. Continuing to run the appliance with an active fault may cause secondary damage.
JennAir Support Center technicians carry the most common replacement parts on every service vehicle. In most cases, we diagnose and complete the repair in a single visit.
Typical ranges based on our service history:
All repairs include a 30 day parts and labor warranty. A written estimate is provided before any work begins.
Error Code Directory
Complete list with diagnosis guides.
| Code | Meaning | Severity | Symptom |
|---|---|---|---|
| F1-E0 | F1-E0 – EEPROM Communication Error | High | The electronic oven control (EOC) board cannot read its EEPROM memory chip.... |
| F2-E0 | F2-E0 – Oven Over-Temperature | Critical | The oven cavity temperature has exceeded the maximum safe limit (approximately 615°F... |
| F3-E0 | F3-E0 – Oven Temperature Sensor Open | Medium | The oven RTD temperature sensor probe is reading open circuit (infinite resistance).... |
| F3-E1 | F3-E1 – Oven Temperature Sensor Shorted | High | The oven temperature sensor is reading near-zero resistance (short circuit). The control... |
| F5-E1 | F5-E1 – Door Latch Not Engaging | High | The self-clean door latch motor is not completing its locking cycle. The... |
| F6-E0 | F6-E0 – Communication Line Open | Medium | The communication line between the oven control board and the user interface... |
| F9-E0 | F9-E0 – Door Lock Failure | High | The oven door failed to lock or unlock during a self-clean cycle.... |
FAQ
Not seeing your specific issue? A two-minute phone diagnosis usually narrows it down.
Call (800) 555-0190Uneven baking in JennAir ranges is most often caused by a weak or partially failed bake element that glows but does not produce full wattage. In dual-fuel models, the gas burners may have dirty or misaligned burner caps. JennAir RISE and NOIR ranges use the same internal components — both are repairable with genuine OEM parts.
Food debris clogging the igniter port or a misaligned burner cap after cleaning are the most common causes. Clean the igniter tip with a soft brush and ensure the cap sits flat. JennAir ranges with brass burners (RISE expression) are particularly susceptible to cap misalignment. If clicking continues without lighting, the igniter electrode or spark module has failed.
JennAir ranges use F-code errors (F1, F2, F5, etc.) to indicate specific faults — oven sensor failures, door lock errors, control board issues, and more. The exact meaning depends on the model. Our technicians have diagnostic tools to read the full error history from the control board.
Most JennAir dual-fuel ranges can be converted from natural gas to LP (propane) using an official JennAir LP conversion kit. The conversion involves changing orifices on all burners and adjusting the pressure regulator. This must be performed by a qualified technician to maintain safe operation and warranty coverage.
Book Your Repair
Factory-trained technicians. Genuine OEM parts. 30 day warranty. Most appointments confirmed within 2 hours.
We'll confirm within 2 hours
Schedule Service
Same-day service available. Factory-trained technicians. Genuine OEM parts. 30 day warranty on every repair.